Datasheets
Documents
Document Name | Size | Published | Modified | |
---|---|---|---|---|
PC-R302Series Datasheet | 123.04 kB | 11/30/-1 | 11/30/-1 | |
pcr-sin06series Datasheet
The PCR-SIN06 Ring Generator Series offers a line of high performance, low cost ring generators with an advanced constant output power driving stage. The series consists of ring generators for
input voltages of 12, 24 and 48Vdc, and each unit supports all popular ringing frequencies: 16.7, 20, 25 and 50Hz. The PCR-SIN06 Ring Generator can continuously support up to 12 standard North
American REN loads, providing a low THD sine wave ringing signal.
|
120.35 kB | 11/30/-1 | 11/30/-1 | |
PCR-SIN15V48F00 Datasheet
The PCR-SIN15V48F00 Ring Generator offers high performance with an advanced overload protection mechanism. Each unit includes an internal crystal oscillator and supports all popular ringing frequencies of 16.7, 20, 25 and 50Hz. The PCR-SIN15V48F00 can continuously support up to 40 standard North American REN loads, providing a low THD sine wave ringing signal. The output ringing signal amplitude defaults to 86Vrms and can be externally adjusted to any value ranging between 45-100Vrms
|
89.9 kB | 11/30/-1 | 11/30/-1 | |
PD LX8580A rev1.4c Datasheet | 584.33 kB | 11/30/-1 | 11/30/-1 | |
PD LX1692 rev1.2 Datasheet | 310.25 kB | 11/30/-1 | 11/30/-1 | |
PD LX1692A rev1 0 Datasheet
Key Features:
For Wide Voltage Range Inverter Application (7V to 22V)
Patent resonant strike for unsurpassed striking power combined with best efficiency
Low Stress to transformers
Excellent open circuit voltage regulation reduces transformer breakdown voltage requirements while striking higher voltage
lamps
One inverter for multiple panel types
Wide Dimming Range
Analog Dimming: >3 to 1
Digital Dimming : >20 to 1
Combined: >60 to 1
Fool-Proof Striking
Programmable Burst Dimming Frequency
Programmable Time Out Protection
Fixed Operating Frequency
Open lamp voltage protection, Short lamp protection, Arc Protection
Compatible with Existing Transformers
|
93.78 kB | 11/30/-1 | 11/30/-1 | |
PD LX1692B rev1.1 Datasheet | 300.89 kB | 11/30/-1 | 11/30/-1 | |
pd lx1696 rev1.0 Datasheet
Key Features:
For Wide Voltage Range Inverter Application (7V to 22V)
Patented resonant Lamp Strike for Unsurpassed Striking Power Combined with Best Efficiency
Reduced Corona Stress To Transformers
Wide Dimming Range
• Direct Low PWM Brightness Control Input Provides > 300:1 Capability
• DC Brightness Control Input Provides > 80:1 capability
Programmable Burst Dimming Frequency
Programmable Time Out Protection
Fixed Operating Frequency
Open lamp voltage protection, Short lamp protection, Arc Protection2
Compatible with Existing Transformers
|
95.02 kB | 11/30/-1 | 11/30/-1 | |
PD LX1736 rev1.0 Datasheet | 187.74 kB | 11/30/-1 | 11/30/-1 | |
PD LX2207 rev1.0 Datasheet | 391.57 kB | 11/30/-1 | 11/30/-1 | |
PD LX2208 rev1.0 Datasheet
The LX2208 is a single cell Lithium Ion or Lithium Polymer battery charger. The controller will charge a single cell Li-Ion battery from either a wall adapter or a USB power source. A low under-voltage lockout level increases usable charging range from a current limited power source. In addition, there is a linear die temperature thermal control loop, which limits the heat dissipation while still charging the battery. There are three logic selectable and programmable charge current levels: the high charge programming level is typically set for charging from the wall adapter, the low level charge programming is typically set to 500mA for full USB charging and 100mA (20%) for reduced USB charging.
In addition to setting the high-level charge current, the HCP programming resistor also sets the termination current at 10% of the constant current level and the conditioning current at 5% of the constant current level. Power status indicators STAT and can be configured to show charge in progress, battery fully charged and external power on. The STAT pin is capable of sourcing or sinking 5mA. The output is an open drain output and can sink 10mA.
The LX2208 enters a low quiescent current shut down when power is removed from the IN pin or when it is logically shutdown to minimize battery drain.
Protection features include: under voltage lock out, reverse current blocking on the IN pin, internal die temperature thermal loop to reduce charge current to maintain a safe die temperature, and a unsafe battery temperature charge inhibitor. For charging deeply discharged batteries, the controller includes a conditioning charge mode. The LX2208 comes in a 3x3mm 12 pin MLPD package.
|
250.64 kB | 11/30/-1 | 11/30/-1 | |
PD LX432 rev1.2d Datasheet
Key Features:
Low Voltage Operation: 1.24V Reference
Initial Voltage Reference Accuracy 1%
Adjustable Output Voltage From VREF to 20V
Typical Output Dynamic Impedance Less Than 250m Ohm
Sink Current Capability 80µA To 20mA
Direct Alternative To TLV431
Please see datasheet for further details.
|
215.58 kB | 11/30/-1 | 11/30/-1 | |
PD LX5530 rev1 0a Datasheet
Key Features:
Broadband 4.9 – 5.9GHz Operation
Advanced InGaP HBT
Single-Polarity 3 – 5V Supply
Power Gain up to ~ 33dB for VC=5V, Icq = 250mA
Power Gain > ~28dB across 4.9-5.85GHz
OFDM Mask Compliance Power Pout ~ +25dBm over 4.9-5.85GHz (ACPR ~ -50dBc @ ±30MHz Offset)
Pout up to +23dBm with EVM ~3% (VC = 5V)
EVM < ~2.5% for Pout=+21dBm across 4.9-
5.85GHz (VC = 5V)
EVM < ~2.5% for Pout=+19dBm across 4.9-
5.85GHz (VC = 4V)
Total Current ~250mA for Pout = +20dBm, Duty Cycle = 99% (VC= 4V)
Complete On-Chip Input Match
Simple Output Match for Optimal Broadband EVM
On-Chip RF Decoupling
Temperature-Compensated On-Chip Output Power Detector with Wide Dynamic Range
Small Footprint: 3x3mm
Low Profile: 0.9mm
|
306.2 kB | 11/30/-1 | 11/30/-1 | |
PD LX5530 rev1 0a Datasheet | 306.2 kB | 11/30/-1 | 11/30/-1 | |
PD LXM1617-05-4x 1.1 Datasheet
UL file number added
|
167.21 kB | 11/30/-1 | 11/30/-1 | |
PD LXM1623-05-44 Datasheet
Key Features:
Externally Programmable Maximum Output Current
Easy to Use Brightness Control
RangeMAX Wide Range Dimming
Output Open & Short-Circuit Protection and Automatic Strike-Voltage Regulation and Timeout
Fixed Frequency Operation
Rated From -20 to 70°C
|
649.51 kB | 11/30/-1 | 11/30/-1 | |
PD LXMG1930-28-0x rev 1.1 Datasheet
LXMG1930-28-0x module is a boost white LED driver for medium size LCD LED backlight panels. It is designed to drive up to three strings of LEDs to a maximum of 35V at up to 50mA per string.
The module consists of a boost converter and three programmable 15 to 50 mA precision current sinks. It is designed to work over a wide input voltage range (4.75V to 28V) providing maximum flexibility. However the converter is a boost only design requiring the input supply voltage to not exceed the output LED string voltage.
The module provides a dimming input: BRITE_A which adjusts the LED display brightness by controlling the amplitude of the LED string current.
The BRITE_A input is very flexible and can be controlled by a PWM signal, the application of a DC control voltage or use of a potentiometer tied as a rheostat. Precision current mirror circuitry typically provides for 1% percent string to string matching at the rated output current. The magnitude of the string current is easily programmed, in 5mA steps through an on board DIP switch.
The LXMG1930-28-0x includes over voltage protection (OVP), and short and open LED protection. If one string opens, its current sink will be disabled and the other strings will continue to operate normally. Likewise if one or several LEDs in a string short it will continue to function with no adverse affect on the other strings. With the use of an external thermistor the module can provide LED current fold back in an over temperature situation.
The module comes in a small form factor PCB and uses an 8 pin input and one of three output connectors.
|
190.17 kB | 11/30/-1 | 11/30/-1 | |
phv6 Datasheet
High voltage rectifier assembly 8KV-80KV. Up to 15A current rating oil cooled.
|
92.02 kB | 11/30/-1 | 11/30/-1 | |
PS LX3055 rev1 0 Datasheet
Key Features:
LX3055 single die
oplanar Waveguide , 50?
High Responsivity
Low Dark Current
High Bandwidth
Anode/Cathode on Illuminated Side
125µm Pad pitch
Die good for bond wire or flip chip applications
Description:
Microsemi’s InGaAs/InP PIN Photo Diode chips are ideal for high bandwidth 1310nm and 1550nm optical networking applications.
|
255.93 kB | 11/30/-1 | 11/30/-1 | |
r702 Datasheet
30A,100V-600V rectifiers and fast recovery rectifiers in TO3 package.
|
93.43 kB | 11/30/-1 | 11/30/-1 |