Datasheets
Documents
Document Name | Size | Published | Modified | |
---|---|---|---|---|
NX2415DS Datasheet
NX2415 Datasheet
|
652.62 kB | 11/30/-1 | 11/30/-1 | |
NX2422DS Datasheet
NX2422 Datasheet
|
652.62 kB | 11/30/-1 | 11/30/-1 | |
NX2423DS Datasheet The NX2423 is a two-phase PWM controller with integrated FET driver designed for low voltage high current application. The two phase synchronous buck converter offers ripple cancelation for both input and output. The NX2423 uses differential remote sensing using either current sense resistor or inductor DCR sensing to achieve accurate current matching between the two channels. Differential sensing eliminates the error caused by PCB board trace resistance that otherwise presents when using a single ended voltage sensing. |
662.42 kB | 11/30/-1 | 11/30/-1 | |
NX2601 Datasheet
DUAL SYNCHRONOUS PWM CONTROLLER WITH NMOS LDO
CONTROLLER AND 5V BIAS REGULATOR
|
1.4 MB | 11/30/-1 | 11/30/-1 | |
NX2710DS Datasheet
SINGLE CHANNEL PWM CONTROLLER WITH NMOS LDO
CONTROLLER AND 5V BIAS REGULATOR
|
746.02 kB | 11/30/-1 | 11/30/-1 | |
NX2837DS Datasheet The NX2837 controller IC is a single power supply synchronous Buck controller IC designed for step down DC to DC converter applications. NX2837 is optimized to convert bus voltages from 9V to 22V to fixed 5V output. This switching 5V output is the input supply of an internal 3.3V LDO which can provide output current up to 700mA. An internal regulator converts bus voltage to 5V, which provides voltage supply to internal logic and driver circuit. The NX2837 operates at 350kHz and employs fixed loss-less current limiting by sensing the Rdson of synchronous MOSFET followed by hiccup feature.Feedback under voltage triggers Hiccup. |
1.23 MB | 11/30/-1 | 11/30/-1 | |
NX2838DS Datasheet The NX2838 controller IC is a single power supply synchronous Buck controller IC designed for step down DC to DC converter applications. NX2838 is optimized to convert bus voltages from 8V to 32V to output voltage as low as 0.8V. The internal 3.3V output LDO can provide output current up to 700mA. An internal regulator converts bus voltage to 5V, which provides voltage supply to internal logic and driver circuit. The NX2838 operates from 200kHz to 1MHz and employs loss-less current limiting by sensing the Rdson of synchronous MOSFET followed by hiccup feature.Feedback under voltage triggers Hiccup. |
556.56 kB | 11/30/-1 | 11/30/-1 | |
NX4108-12DS Datasheet The NX4108-12 is a current mode PWM buck switcher with internal compensation and fixed 1.2V output voltage, can provide up to 1A output current with FET on board. It operates from 2.8V to 5.5V which is ideal for the application with single cell Li-Ion battery as well as other 3.3V input bus supply applications. Switching frequency is fixed 1MHz, small surface mount inductors and capacitors are allowed to use, make it good for portable applications. |
270.96 kB | 11/30/-1 | 11/30/-1 | |
NX4108-15DS Datasheet The NX4108-15 is a current mode PWM buck switcher with internal compensation and fixed 1.5V output voltage, can provide up to 1A output current with FET on board. It operates from 2.8V to 5.5V which is ideal for the application with single cell Li-Ion battery as well as other 3.3V input bus supply applications. Switching frequency is fixed 1MHz, small surface mount inductors and capacitors are allowed to use, make it good for portable applications. |
173.53 kB | 11/30/-1 | 11/30/-1 | |
NX4108-18DS Datasheet The NX4108-18 is a current mode PWM buck switcher with internal compensation and fixed 1.8V output voltage, can provide up to 1A output current with FET on |
143.05 kB | 11/30/-1 | 11/30/-1 | |
NX4108-33DS Datasheet The NX4108-33 is a current mode PWM buck switcher with internal compensation and fixed 3.3V output voltage, can provide up to 1A output current with FET on |
222.63 kB | 11/30/-1 | 11/30/-1 | |
NX4108ds Datasheet The NX4108 is a current mode PWM buck switcher with internal compensation that can provide up to 1A output current with FET on board. It operates from 2.8V to 5.5V with output as low as 0.6V which is ideal for applications with a single cell Li-Ion battery as well as other 3.3V input bus supply applications. Switching frequency is fixed at 1MHz, small surface mount inductors and capacitors are allowed for use, making it well-suited for portable applications. FEATURES: |
817.3 kB | 11/30/-1 | 11/30/-1 | |
NX4110DS Datasheet The NX4110 is a current mode PWM buck switcher with internal compensation that can provide up to 1A output current with the FET on board. It operates from 2.8V to 5.5V Vin with an output voltage as low as 0.6V making it ideal for applications using single cell Li-Ion batteries as well as other 3.3V input bus supply applications. Switching frequency is fixed at 1MHz. Small surface mount inductors and capacitors can be used with the NX4110, making it ideal for portable applications. The NX4110 is available in 5-pin SOT23 package. FEATURES: APPLICATIONS: |
819.63 kB | 11/30/-1 | 11/30/-1 | |
NX7101 Datasheet | 340.69 kB | 08/20/2014 | 08/20/2014 | |
NX7102 Datasheet | 857.6 kB | 09/24/2013 | 09/24/2013 | |
NX9415 Datasheet | 260.6 kB | 04/01/2014 | 04/01/2014 | |
NX9548 Datasheet | 897.78 kB | 07/26/2013 | 07/26/2013 | |
P4KE Datasheet
This family of high-reliability, plastic packaged Transient Voltage Suppressors offer high reliability at an affordable price. Standoff voltage values range from 5.8 to 342 volts and 5% or 10% tolerance options are available. Source control is standard and three increasingly stringent screening options for enhanced reliability are available.
|
428.84 kB | 11/30/-1 | 09/15/2015 | |
P5KE Datasheet MP5KE5.0A – MP5KE170CA series |
465.24 kB | 11/30/-1 | 09/15/2015 | |
P6KE Datasheet
MP6KE6.8A - MP6KE200CA(e3) datasheet
|
483.22 kB | 11/30/-1 | 09/15/2015 |